These measurements are taken from an Early Ford Bronco with factory sheet metal. However, all Broncos vary slightly from one to another. Please use these measurements for reference only. Keep in mind, taking your own measurements is always best, and Tom’s Bronco Parts assumes no liability.
Bronco Schematics
Bronco Floor Factory Bucket Seat Hole Locations
Curious as to where your factory bucket seat holes need to be drilled? These measurements are taken from an Early Ford Bronco with factory sheet metal. However, all Broncos vary slightly from one to another. Please use these measurements for reference only. Keep in mind, taking your own measurements is always best, and Tom’s Bronco […]
Radius Arm Drop Brackets Instructions
Click this link to access instructions for our #6897 Radius Arm Drop Brackets for 66-77 Ford Bronco.
66-77 Ford Bronco Receiver Hitch Instructions #0928
The following is an instruction guide to install our Class III Receiver Hitch for 66-77 Ford Broncos. This hitch can be installed with either factory rear fuel tanks or 23 gallon fuel tanks. It also will work with stock rear bumpers as well as our rear impact or pre-runner style bumpers. Click here for more […]
66-77 Ford Bronco Transfer Case Yoke Installation
You can download the pdf instructions here. — Apply a thin film of grease to the yoke where the seal will ride. 4. This groove is where the o-ring seats. It prevents the oil from seeping out of the splines. — Install the o-ring into the groove as shown. — The O-ring is […]
NV3550 5-Speed Transmission Conversion Install Video Series
66-77 Ford Bronco NV3550 Transmission Conversion This 7 part video series covers installation of our 66-77 Ford Bronco NV3550 Manual Transmission Swap Kit. To purchase this kit go here: BUY IT: 66-77 Ford Bronco NV3550 Transmission Swap Kit To see the written instructions go here: INSTALLATION: 66-77 Ford Bronco NV3550 Transmission Swap Kit Part 1: […]
3 Point Seat Belt Installation
Tom’s Bronco Parts 3-Point Seat Belts Instructions in PDF Format The above installation instructions will show you how to install our TBP 3-point Shoulder Seat Belts into your 66-77 Ford Bronco. NOTE: You MUST have an interior bar/roll cage in order to install these seat belts properly.
66-77 Ford Bronco Seat Mounting Holes
Please see the attached image for a diagram with measurements of the Early Bronco Front and Rear Seat Mounting Hole Locations. This diagram is extremely useful when installing new floor pans in your Classic Bronco and you have forgotten to take these measurements prior to cutting the floor. 66-77 Ford Bronco Seat Floor Hole Locations
1996 Ford Bronco Custom Aftermarket Front Seat Installation
I had the privilege of purchasing some nice new fronts seats for my 1996 Full Size Ford Bronco from Tom’s Bronco Parts. Now, I had the existing (stock) seat rails, so I needed to mount these custom seats to those since Tom’s doesn’t sell new seat rails for these Broncos. Overall, this was a really […]
66-73 Ford Bronco Steering Wheel Horn Button Schematic
See the attached picture for a schematic of the 66-73 Ford Bronco Horn Button Assembly on the Factory Original Steering Wheel. It is incorporated with Tom’s Bronco Parts part numbers for easy reference and replacement part reordering.
H-Block/Prop Valve Brake Warning Switch Adjustment
The stock Early Bronco was equipped with a Brake Warning Light on the dash which is used to indicate when there is a loss of brake fluid pressure to the front or rear brake system. When this loss of pressure occurs, the brake imbalance switch in the Brake Junction Block/Prop Valve will be pushed off-center […]
“No Modify” Power Brake Kit For Early Bronco
You can download these instructions as a PDF here: No Modify Power Brake Kit Instructions for 66-77 Ford Bronco Instructions on how to install the early Bronco power brake kit Above are photos of the kit as shipped. Included is the booster, bracket, master cylinder, master cylinder brake lines, adjustable pushrod with rubber seal and […]